Olympus Carrying Case PFL 01 User Manual

Instruction Manual  
Waterproof Case  
PFL-01  
For the electronic flash  
FL-20  
Thank you for buying the Underwater Case PFL-01.  
Please read this instruction manual carefully and use the product safely  
and correctly.  
Please keep this instruction manual for reference after reading it.  
Wrong use may cause damage to the flash on the inside from water  
leakage, and repair may not be possible.  
Before use, perform an advance check as described in this manual.  
 
Disclaimer  
WARNING  
Unauthorised copying of this manual in part or in full, except for private  
use, is prohibited. Unauthorised reproduction is strictly prohibited.  
1. Keep this product out of the reach of babies, infants, and children.  
There is the possibility of occurrence of the following types of  
accidents.  
ț Injury by dropping onto the body from a height.  
ț Injury from parts of the body getting caught in parts which open  
and close.  
ț Swallowing of small parts. Please consult a physician immediately  
if any parts have been swallowed.  
ț Triggering of the flash in front of the eyes may cause permanent  
vision impairment etc.  
OLYMPUS CORPORATION shall not be responsible in any way  
for lost profits or any claims by third parties in case of any damage  
occurring from incorrect use of this product.  
OLYMPUS CORPORATION shall not be responsible in any way  
for damage, lost profits, etc. caused by the loss of image data due  
to defects, disassembly, repair or modification of this product by  
people, other than third parties specifically authorised by  
OLYMPUS CORPORATION or for other reasons.  
2. Never store this product with an electronic flash with batteries  
inside. Battery leakage could result in a fire or an explosion.  
3. If water comes into contact with the electronic flash inside this  
product, remove the batteries from the flash immediately.  
Otherwise, hydrogen gas could be produced, which could lead to a  
fire or an explosion.  
4. This product is made of resin. There is the possibility that injuries  
may be caused when it becomes broken because of strong impact  
with a rock or other hard objects. Please handle with sufficient care.  
5. The silica gel and the grease for silicone O-rings for this product  
are not edible.  
Please read the following before using the product  
This product has been precision-crafted from high quality  
polycarbonate. When used correctly, it lets you take photographs  
safely up to a water pressure equivalent to a depth of 40 metres.  
To ensure correct and safe use of the case, please read all  
instructions on handling and carrying out the system check as well  
as care, maintenance and storage of the case.  
OLYMPUS CORPORATION shall in no way be responsible for  
damage caused by water to the flash contained in the case.  
OLYMPUS CORPORATION shall not pay any compensation for  
accidents (injuries or material damage) that may occur during the use  
of this product.  
CAUTION  
The electronic flash cannot be used in AUTO mode when it is  
inserted in this case.  
A commercially available bracket arm is required to use this  
product in combination with the PT-020.  
1. Do not disassemble or modify this product. This may cause water  
leakage or trouble. In case of disassembly or modification by  
persons other than those appointed by OLYMPUS CORPORATION,  
the guarantee shall not apply.  
2. Do not place this product at locations with abnormally high or  
abnormally low temperatures or at locations with extreme  
temperature changes. The product may deteriorate.  
3. Opening and closing at locations with much sand, dust, or dirt may  
impair the waterproof characteristic and cause water leakage. This  
should be avoided.  
4. This product is suitable for use at water pressures equivalent to  
depths of up to 40 meters. Please note that diving at depths  
greater than 40 meters may result in deformation or damage to this  
product, as well as to the camera and lens. In this case, water  
penetration may occur.  
For safe use  
This instruction manual uses various pictographs for correct use of  
the product and to prevent danger to the user and other persons as  
well as property damage. These pictographs and their meanings are  
shown below.  
This indicates contents for which the possibility of  
human death or severe injury in case of handling under  
disregard of this indication can be assumed.  
WARNING  
CAUTION
This indicates contents for which the possibility of  
human injury or the possibility of material damage in  
case of handling under disregard of this indication can  
be assumed.  
E-1  
E-2  
 
5. Rough handling, such as jumping into the water with the case in  
your hand or in an outside pocket or throwing the case into the  
water could lead to water penetration. Please always take care  
when using the case.  
6. If the electronic flash contained in the case gets wet, wipe off all  
moisture immediately and check the flash is working correctly.  
7. Before traveling by air, please make sure you remove the O-rings,  
otherwise the difference in air pressure may make it impossible to  
open the case.  
For Prevention of Water Leakage Accidents  
If water gets inside this product during use, irreparable damage may  
be caused to the electronic flash inside the case. Please note the  
following points.  
1. When sealing this product, make sure that no hairs, fibers, sand  
particles or other foreign matter stick not only to the O-ring, but  
also to the contact surface. Even a single hair or a single grain of  
sand may cause water leakage. Please check with special care.  
2. The O-ring is a consumption product. Please replace it at least  
8. To ensure safe and trouble-free handling and operation of the  
electronic flash in this product, please read the flash’s instruction  
manual carefully.  
Examples for foreign matter sticking to the O-ring  
9. When sealing this product, please take care to ensure no foreign  
matter such as sand, dirt or hair is on the O-rings or contact  
surfaces.  
10.Before storing this product, always be sure to take out the flash.  
11.When using this product, do not fire the flash at close range to a  
person or animal.  
Batteries  
Hair  
Fibers  
Grains of sand  
To supply power to the electronic flash, we recommend you use  
two LR6 alkaline batteries, two lithium batteries, two Ni-Mn  
batteries, two Ni-Mh batteries or two Ni-Cd batteries.  
Keep the batteries’ contacts away from damp and humidity to avoid  
impairing performance and/or causing an accident.  
For other battery handling precautions, please read the relevant  
sections in the electronic flash’s instruction manual.  
once a year by new one. Also perform maintenance for every use.  
3. Deterioration of the O-ring will progress according to the use  
conditions and the storage conditions. Immediately replace the O-ring  
by a new one if it is damaged, shows cracks, or has lost its elasticity.  
4. At the time of O-ring maintenance, clean the inside of the O-ring  
groove and confirm the absence of dirt, dust, sand, and other  
foreign matter.  
5. Apply the specified silicone O-ring grease to the O-ring.  
6. The waterproof function is not effective when the O-ring is not  
installed correctly. When installing the O-ring, take care that it does  
not project from the groove and that it is not twisted. Also, when  
sealing the Case, close the lid after confirming that the O-ring has  
not come out of the groove.  
7. This product is an airtight construction made of plastic (polycarbonate).  
When it is left for a long time in a car, on a boat, at the beach, or at  
other places reaching a high temperature, or when it is subjected for a  
long time to uneven external force, it may be deformed and the  
waterproof function may be lost. Pay sufficient attention to temperature  
control. Also do not place heavy objects onto the product during  
storage or transport, and avoid unreasonable storage.  
8. When the O-ring contact surface is pressed strongly from the  
E-3  
E-4  
 
outside of the Case, or when the Case is twisted, the waterproof  
function may be lost. Take care not to exert excessive force.  
9. Please be sure to perform the advance test and the final test each  
time before using the case.  
10.If you see any drops of water or any other signs of water  
penetration during use, stop the dive immediately. Carefully dry  
from the flash and waterproof case, and then perform the “Final  
System Check” and confirm whether any water actually penetrated  
this product.  
Explanation  
Chemicals which cannot be used  
Do not clean the Case with alcohol, gasoline, thinner  
or other volatile organic solvents or with chemical  
detergents etc. Pure water or lukewarm water is  
sufficient.  
Volatile organic solvents,  
chemical detergents  
Do not use anticorrosion agents. The metal parts use  
stainless steel or brass, and washing with pure water  
is sufficient.  
Anticorrosion agent  
Commercial defogging  
agents  
Do not use commercial defogging agents. Always  
use the specified desiccant silica gel.  
Use only the specified silicone grease for the silicone  
O-ring, as otherwise the O-ring surface may  
deteriorate and water leakage may be caused.  
Handling the Product  
Grease other than specified  
silicone grease  
Use or storage of the product at the following locations may cause  
defective operation, defects, trouble, damage, fire, internal  
clouding, or water leakage. Always avoid these locations.  
ț Places where high temperatures exist, such as in direct sunlight, in  
a closed vehicle, etc., and/or where extreme differences in  
temperatures exist.  
Do not use adhesive for repairs or other purposes.  
When repair is required, please contact a dealer or a  
service station of our company.  
Adhesive  
Do not perform operations other than specified in this instruction  
manual, do not remove or modify parts other than specified, and do  
not use parts other than specified.  
Any troubles in taking pictures or with the equipment resulting from  
the above actions shall be outside the guarantee.  
OLYMPUS CORPORATION does not assume any liability for  
damage to the flash caused by water penetration.  
OLYMPUS CORPORATION shall not pay any compensation for  
accidents (injury or material damage) at the time of use.  
ț Places where there is a lot of dust.  
ț Places where there are open fires.  
ț Places subject to vibrations.  
ț Places where volatile chemicals are stored or used.  
ț water deeper than 40 meters.  
This product is made of polycarbonate resin with excellent impact  
resistance, but it may be damaged by scraping against rocks etc. It  
also may break when it hits hard objects or is dropped.  
This product is not intended as a case to protect the internal flash  
from heavy knocks. If the case is subjected to a heavy knock or  
significant pressure, the flash inside may be severely damaged.  
When this product is not used for a long time, the O-rings may  
deteriorate, diminishing its waterproof properties. Therefore, please  
use the case only after first performing the first and final system  
checks described in this instruction manual.  
Do not apply excessive force to the arm mount and underwater  
TTL cable connector.  
The range of the flash underwater may be lower than on land depending  
on the conditions at the time of shooting (clarity of the water, suspended  
matter, etc.). Be sure to check the image before actual shooting.  
Do not use the following chemicals for cleaning, corrosion prevention,  
prevention of fogging, repair or other purposes. When these are used  
for the Case directly or indirectly (with the chemicals in vaporized state),  
they may cause cracking under high pressure or other problems.  
E-5  
E-6  
 
Contents  
Disclaimer⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-1  
Please read the following before using the product ⋯⋯⋯⋯⋯E-1  
For safe use⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-1  
Batteries ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-3  
For Prevention of Water Leakage Accidents ⋯⋯⋯⋯⋯⋯⋯⋯E-4  
Handling the Product ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-5  
4. Taking photos underwater ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-22  
Setting the flash mode ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-22  
Underwater TTL AUTO shooting ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-22  
Underwater MANUAL shooting ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-22  
5. Handling after use ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-23  
Wipe off any waterdrop ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-23  
Removing the electronic flash⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-24  
Cleaning the case with pure water⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-24  
Disconnecting the TTL cable ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-25  
Drying the case and TTL cable ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-25  
Contents ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-7-8  
1. Preparations ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-9  
Checking the contents of the package ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-9  
Names of the parts ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-10  
Preparing the case ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-11  
Attaching/removing/the diffuser plate ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-11  
Connection to the camera case ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-12  
1) Connecting the underwater TTL cable ⋯⋯⋯⋯⋯⋯⋯⋯E-12  
2) Connecting the hot shoe cable ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-13  
3) Mounting on an arm ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-14  
6. Maintaining the Waterproof Function ⋯⋯⋯⋯⋯E-26  
Remove the O-ring. ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-26  
Remove any sand, dirt, etc. ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-26  
Install the O-ring. ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-27  
How to Apply Grease to the O-ring ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-27  
Replace consumable products. ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-28  
2. Advance Check of the Case ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-15  
7. Appendix⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-29  
Q & A on the use of the PFL-01 ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-29  
After-sale Service ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-34  
Specifications ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-35  
Advance test before use ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-15  
Advance Test⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-15  
3. Insertion of the electronic flash ⋯⋯⋯⋯⋯⋯⋯⋯E-16  
Checking the electronic flash ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-16  
Checking the Batteries ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-16  
Inserting in the case ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-16  
Which electronic flashes can be used? ⋯⋯⋯⋯⋯⋯⋯⋯⋯E-16  
Opening the case ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-17  
Inserting the flash ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-17  
Insertion of silica gel ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-18  
Check the loading status ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-19  
Seal the Case ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-19  
Perform the final check ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-20  
Visual inspection ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-20  
Setting she flush power to ON and OFF ⋯⋯⋯⋯⋯⋯⋯⋯E-20  
Final Test ⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯E-21  
E-7  
E-8  
 
Names of the parts  
1. Preparations  
Check the contents of the package.  
Check that all accessories are in the box.  
Contact your dealer if accessories should be missing or damaged.  
WARRANTY  
(販売店控え)  
取扱説明書  
エレクトロニックフラッシュ  
FL-20用  
本保証書は、本記載内容で無料修理を行うことをお約束するものです。  
お買い上げの日から下記期間中、万一故障が発  
お買い上げ販売店、または当社サービスステーションにご依頼ください。  
生した場合は、本契約書を添付ご持参の上  
*Mode dial  
Hot shoe  
本保証書は日本において有効です。  
期  間  
お買上げ  
本体1年間  
年  月   
This is limited warranty for  
a
1
year from your date of  
防水プロテクタ  
purchase. Useful only in  
Japan.  
住所 Address  
Buckle hook  
Underwater TTL cable connector cap  
Grease for silicone O-ring (white cap)  
Silica gel  
お客様  
PFL-01  
氏名 Name      性別(男・女)、年齢(  才)  
Customer  
                           
            TEL     
(
   )  
〔必ず店名印をしてください。〕  
*Test button  
販売店  
Dealer's  
name and  
address  
Buckle open/close lever  
Light-emitting window  
Arm mount  
JAPAN  
品名  
型名  
防水  
防塵  
プロテクタ  
Model  
O-ring removal pick  
Buckle opener  
Serial NO.  
■このたびは水プロテクタPFL-01をお買上げいただきりがとうござ  
います。  
■この説明書をよくお読みのうえ全に正しくお使いくださいの  
説明書はお読みになった後ず保してください。  
保証責  
任者  
保証履行者  
〒192-0032 東京都八王子市石川町2951  
お問い合せ先/サービスステーション  
       03(3292)1931          
■誤った使い方をされると水漏れにのフラ  
になる場合がりま。  
■ご使用にはの説明書に従いず事前  
シュ理不能  
を実施してください。  
Diffuser plate strap  
Diffuser plate  
Arm attaching adapter  
O-ring (POL-201A)  
O-ring (POL-201B)  
Underwater TTL cable connector  
Note : The case parts marked with an asterisk (*) correspond to functions  
on the electronic flash. Consequently, operation of these parts  
activates the corresponding functions in the flash. For details on  
these functions, refer to the electronic flash’s instruction manual.  
E-9  
E-10  
 
Preparing the case  
Connection to the camera case  
To perform underwater TTL shooting using this case, connect the  
underwater TTL cable between this case and the camera case. Connect  
the hot shoe cable (provided with this case) between the TTL cable  
connector in the camera case and the camera’s hot shoe.  
Before shooting, prepare the case as described below.  
Attaching/removing/ the diffuser plate  
This case is equipped with a diffuser plate that can be used to  
attenuate the flash light.  
Use the diffuser plate to weaken the shadow of the subject as well as  
to attenuate the light.  
The diffuser plate can be attached or removed as shown below.  
1)Connecting the underwater TTL cable  
Make sure that both case’s are dry, and loosen and remove the  
TTL cable connector cap from each case.  
After removing the cap, connect either end of the underwater TTL  
cable connector to the uncapped TTL cable connector in the case.  
Pay attention to the following points ; check the orientation of  
the 5 pins in the TTL cable’s connector and align it so that the pins  
fit into the corresponding receptacles in the case’s TTL connectors  
turn the lock dial screw on the TTL cable’s connector all the way  
clockwise to lock the connector firmly.  
The underwater TTL cable can be disconnected from each case by  
reversing  
the  
above  
connection steps. In the final  
step, screw the cap back  
onto the case’s TTL cable  
connector until it is stops.  
:
When not using the diffuser plate, place it on the center  
part on the front of the case as shown on the right.  
Lock dial screw  
CAUTION  
:
Always make sure that the case are completely dry before  
connecting or disconnecting the underwater TTL cable.  
CAUTION  
• O-rings are attached to the case’s TTL connector caps  
and the underwater TTL cable’s connectors to keep out  
water. If any fibers, sand or hair are attached to an O-  
ring, the integrity of the waterproof function will be  
affected and water penetration may result. Be sure to  
check and remove any foreign matter on the O-rings  
before connecting these connectors.  
• Pay attention to the position of the 5 pins when  
connecting the connectors.  
• Do not use excessive force when tightening the lock dial  
screw on the cable’s connector.  
• When the underwater TTL cable is not connected, be  
sure to put the caps back on the TTL cable connectors.  
E-11  
E-12  
 
2)Connecting the hot shoe cable  
3)Mounting on an arm  
This case can be mounted on a commercially available arm or  
similar tool as described below.  
When using a commercially available arm with a width of 12 mm,  
mount the provided arm-attaching adapter in the direction shown in  
below. When using an arm with a width of 10 mm, mount  
adapter in the direction shown in below.  
Connect the hot shoe cable, provided with this case, between the  
TTL cable connector on the inner side of the camera case and the  
hot shoe of the camera. Pay attention to the following points: ᕃ  
before inserting the camera into the camera case, loosen and  
remove the cap on the TTL cable connector inside the camera  
case; insert the 5-pin connector of the hot shoe cable into the  
TTL cable connector inside the camera case; turn the lock dial  
screw on the hot shoe cable’s connector all the way clockwise to  
lock the connector firmly; insert the camera in the camera case;  
after inserting the camera, insert the hot shoe unit of the hot  
shoe cable all the way into the camera’s hot shoe.  
The hot show cable can be disconnected by reversing the  
connection steps. In the final step, screw the cap back onto the  
TTL cable connector inside the camera case until it stops.  
Insert the commercially purchased arm into the arm mount, and  
then tighten the arm by inserting and turning the provided arm  
mount screw all the way clockwise.  
:
Pay attention to the position of the 5 pins when  
connecting the connectors.  
Do not use excessive force when tightening the lock  
dial screw on the cable’s connector.  
When the hot shoe cable is not connected, be sure to  
put the caps back on the TTL cable connectors.  
CAUTION  
:
• The arm mount of this case has an interval of 12 mm.  
Use care when mounting it on a commercially  
purchased arm.  
CAUTION  
• Do not tighten the arm mount screw with excessive  
force.  
E-13  
E-14  
 
2. Advance Check of the Case  
3. Inserting the electronic flash.  
Advance test before use  
Checking the electronic flash  
This Case has been the subject of thorough quality control for the  
parts during the manufacturing process and thorough function  
inspections during the assembly. In addition, a water pressure test  
is performed with a water pressure tester for all products to confirm  
that the performance conforms to the specifications. However,  
depending on the carrying and storage conditions, the maintenance  
status, etc., the waterproof function may be damaged.  
Load batteries into the electronic flash and perform the flash check  
before inserting the flash in the case.  
Checking the batteries  
Load two LR6 alkaline batteries, two lithium batteries, two Ni-Mn  
batteries, two Ni-Mh batteries or two Ni-Cd batteries as shown  
below.  
Before diving, always perform the following advance test and the  
water leakage test after installation of the flash.  
Manganese batteries cannot be used.  
Set the mode dial to AUTO.  
Advance Test  
When the charge lamp lights up, press the test button and  
ensure that the flash emits light.  
1. Before inserting the electronic flash, take the empty case to the  
intended depth and make sure that no water gets inside the  
case.  
2. Main causes of water leakage are as follows.  
ț The O-ring has not been installed.  
ț A part of the O-ring or the entire O-ring is outside the specified  
groove.  
ț O-ring damage, cracks, deterioration or deformation  
ț Sand, fibers, hair or other foreign matter sticking to the O-ring,  
the O-ring groove or the O-ring contact surface.  
ț Damage to the O-ring groove or the O-ring contact surface.  
ț When closing the Case, check for catching of the hand strap and  
silica gel after the above causes have been eliminated.  
Note:• To avoid running out power during shooting, it is recommended  
to load fully charged batteries before every diving session.  
:
• The most suitable method for checking water leakage  
is to immerse the Case to the intended water depth.  
When this is difficult, water leakage also can be  
checked at a shallow depth with no water pressure. Do  
not feel that this is troublesome, but perform this test.  
• If the advance test should show water leakage with  
normal handling, stop using the Case and contact  
your dealer or an Olympus service station (listed on  
the rear page of this instruction manual).  
CAUTION  
Inserting into the case  
Which electronic flashes can be used?  
The product (PFL-01) is exclusively for use with the FL-20  
Electronic Flash.  
E-15  
E-16  
 
Open the Case.  
Insertion of silica gel  
Insert the buckle opener of the accessory into the buckle opening  
lever as shown in the figure (in direction ) Pull the buckle opener  
slowly (in direction ). When not using the buckle opener, hold the  
buckle opening lever with your thumb and index finger from the side  
and pull it up slowly.  
Before closing the case, place the provided bag of silica gel (to  
prevent fogging) between the right side panel of the flash and the  
case. Insert the bag with the longer, glued side first.  
Inserting the flash  
Carefully insert the FL-20 Electronic Flash into the hot shoe of this  
case. Make sure that the protruding part of the camera’s zoom  
lever fits properly in the notch in case’s zoom lever.  
Follow the steps shown in the illustration; insert the flash all the  
way into the hot shoe; turn and tighten  
the shoe lock dial of the flash.  
To remove the FL-20 from this case, follow these steps; turn and  
loosen the shoe lock dial of the flash; holding the flash’s dial  
firmly with a finger, slide the case out of the flash’s hot shoe.  
:
Insert the silica gel all the way at the specified location and  
with the specified orientation. When the orientation is not  
correct, the silica gel bag will be caught when the Case is  
sealed and water leakage will be caused.  
Attempting to seal the Case with the bag inserted only part of  
the way will cause the silica gel bag to get caught by the O-ring  
and water leakage will occur.  
Once silica gel has been used, the moisture absorption  
performance will be impaired. Always exchange the silica  
gel when the Case is opened and closed.  
CAUTION  
:
Be sure to turn the flash off before inserting it into this case.  
CAUTION  
•Do not apply excessive force to the flash when  
inserting it.  
• When removing the flash from this case, hold the  
flash so as not to drop it.  
E-17  
E-18  
 
Check the loading status.  
Perform the final checks.  
Visual Inspection  
After sealing the Case, check the sealing part of front and rear lid  
visually to confirm that the O-ring is not twisted or out of the groove  
and that no foreign matter has been caught.  
Always perform the following final checks before sealing the Case.  
ț Has the electronic flash been inserted properly into the hot shoe of  
the case?  
ț Has the silica gel been inserted all the way at the specified  
position?  
ț Has the O-ring at the Case opening part been installed properly?  
ț Are the O-ring and the O-ring contact surface on the front lid free of  
dirt and other foreign matter?  
:
Hairs, fibers, and other narrow items are not very apparent,  
but they may cause entry of water, so that special attention  
is required.  
CAUTION  
Seal the Case.  
Setting the flash power to ON and OFF  
When the rear lid is closed  
(quietly, so that the O-ring  
will not come out of the  
groove), the buckles are  
engaged with the edge of the  
rear lid, and the buckle lock  
levers are pushed down in  
arrow direction, the Case will  
be sealed airtight.  
Turn the mode dial knob and confirm that the electronic flash can  
be turned ON and OFF.  
Also turn the mode dial knob and confirm that the flash’s mode dial  
can be switched to TTL AUTO and MANUAL.  
:
After inserting the flash into the case, confirm that the mode  
dial moves. If it does not move, oil or grease may have  
gotten on the mode dial. Wipe it clean.  
CAUTION  
:
Seal the Case by turning both buckle lock levers down in  
arrow direction. When one of the buckles is left open, the  
Case will not be sealed and water leakage will be caused.  
CAUTION  
E-19  
E-20  
 
Final Test  
4. Taking photos underwater  
After the electronic flash has been inserted in the case, you should perform  
the final system check. This covers all tests that you must carry out to make  
sure that no water can enter the case. The tests are easy to do and only take  
about 5 minutes. All you need is a bowl or tub of water.  
Setting the flash mode  
This case enables underwater TTL AUTO shooting.  
The following procedure was originally developed to test for water  
penetration inside the camera case. The test procedure for the waterproof  
flash case is identical, so please follow these steps.  
:
When this case is used, the AUTO mode of the electronic  
flash cannot be used. Even if the mode dial of the flash is  
set to AUTO, it emits light at the maximum intensity.  
CAUTION  
Simple water  
immersion test  
Explanatory  
image  
Hints  
As the Case is transparent,  
waterdrops entering into it can be  
confirmed easily.  
Place the Case  
slowly into the water.  
1
2
3
4
5
6
7
8
Underwater TTL AUTO shooting  
In case of trouble with the O-ring,  
three seconds are enough for water  
to enter. Are there air bubbles  
coming out between the lids?  
Please check carefully.  
Remove the Case from the water and  
check that no water has accumulated at  
the bottom of the Case.  
Turn the case’s mode dial knob to set the  
electronic flash to the TTL AUTO mode.  
For details including the digital camera  
setup, refer to the camera and flash  
instruction manuals.  
At first, immerse the  
Case for only three  
seconds.  
Check that no water  
has entered into the  
Case.  
Is there any water trickling down?  
Next, immerse the  
Case for 30  
seconds.  
Check carefully for air bubbles!  
Do not perform any operation yet,  
but just observe.  
Underwater MANUAL shooting  
Turn the case’s mode dial knob to set the  
electronic flash to the MANUAL mode. For  
details including digital camera setup,  
refer to the camera and flash instruction  
manuals.  
Remove the Case from the water and  
check that no water has accumulated  
at the bottom of the Case.  
Check that no water  
has entered.  
Perform very careful confirmation.  
Check carefully for air bubbles!  
Try operation of the buttons used frequently.  
Check carefully for air bubbles!  
If there is still no entry of water,  
everything is OK!  
Next, check by  
immersing for three  
minutes.  
This is very important!  
:
For the camera’s iris setting and standard shooting range,  
refer to the flash instruction manual.  
CAUTION  
This is the final check.  
Has the silica gel  
become moist?  
Has the silica gel become moist?  
Please check carefully!  
As the inside can be seen, the inspection for  
entry of water also can be made securely!  
The underwater flash shooting range (distance) maybe  
reduced depending on the conditions at the time of shooting  
(clarity of the water, suspended matter, etc.). Be sure to  
check the image on the camera’s LCD monitor before  
actual shooting.  
Now everything is  
all right.  
Now everything is all right!  
Have a nice dive!  
E-21  
E-22  
 
Removing the electronic flash  
5. Handling After Shooting  
Carefully open the case, loosen the  
shoe lock dial of the flash and, while  
holding the mode dial knob on the  
case firmly, slide the flash out of the  
case’s hot shoe.  
Wipe off any waterdrop.  
After underwater shooting, remove  
any drops of water from the case.  
Use pressurized air or a soft, lint-  
free cloth to carefully wipe away  
any moisture from the hinge  
between the front and rear lids, the  
TTL cable connector and the  
buckles.  
:
• After opening the case, always put it down it with the  
O-ring side face-up. Otherwise, dirt or other foreign  
matter could attach itself to the O-rings and/or the  
contact surfaces, allowing water to penetrate the case  
during the next dive.  
CAUTION  
:
• Especially when waterdrops remain between the front  
and the rear lid, they may spill to the inside when the  
Case is opened. Take special care to wipe off all  
waterdrops.  
CAUTION  
• Before removing the flash, make sure the flash’s shoe  
lock dial is loose. Never use force to remove the  
flash. This could damage the flash or the case.  
• When opening the Case, take sufficient care that no  
water will drop from your hair or body onto the Case  
and the flash.  
• Before opening the Case, make sure that your hands  
or gloves are free of sand, fibers, etc.  
• Do not open or close the Case at locations where  
water or sand is to be sprayed. When this cannot be  
avoided because you have to exchange the battery,  
place a sheet downwind from some object and take  
care that no water or sand is sprayed.  
Cleaning the case with pure water  
After using this case, remove the flash, then seal it  
again with the TTL cable still connected, and rinse  
it with pure water as soon as possible. After use in  
salt water, the case should be immersed for an  
extended period of time in a bowl of pure water to  
remove any salt water or salt residues.  
• Never touch the electronic flash and/or batteries when  
your hands are wet with sea water.  
Note: Moisten a towel etc. in advance with pure water and keep it  
in a plastic bag so that you can wipe the salt from your  
hands and fingers before handling the camera.  
:
• Water may enter the case under localized high water pressure (such  
as from a hose.) Before cleaning the case with water, the flash  
should be removed.  
• Operate the mode dial knob and buttons of the case when it is in  
clean tap water to remove any salt from their shafts. Do not  
disassemble the case for cleaning!  
CAUTION  
• If the case is dried before all salt has been removed, this could affect  
its performance. Always make sure all salt has been removed!  
• If the case should be cleaned without the TTL cable connected to it,  
be sure to attach the cap to the connector in advance.  
E-23  
E-24  
 
Disconnecting the TTL cable  
6. Maintaining the Waterproof Function  
After making sure that the case  
and TTL cable are free of water  
drops, loosen the lock dial screw  
and disconnect the TTL cable.  
Remove the O-ring.  
Open the Case and remove the O-ring from the Case.  
Removal of the O-ring  
Insert the O-ring removal pick between the O-ring and the wall of  
the O-ring groove.  
Move the tip of the inserted pick under the O-ring. (Take care not  
to damage the O-ring groove with the tip of the pick.)  
Hold the O-ring with your fingertips after it has come out of the  
groove and remove it from the Case.  
:
• Do not apply excessive force when disconnecting the TTL cable.  
• Make sure that no foreign matter such as dirt is attached to the  
O-ring of the connector. Should any foreign matter be attached  
to it, wipe it clean with a clean, lint-free cloth.  
CAUTION  
• Be sure to attach the cap to the TTL cable connector after  
disconnecting the cable.  
Remove any sand, dirt, etc.  
After visually checking that dirt has been removed from the O-ring,  
checking for attached sand and other foreign matter, as well as for  
damage and cracks can be done by squeezing the entire circumference  
of the O-ring lightly with your fingertips.  
Drying the case and TTL cable  
After washing the case and TTL cable, dry them with a clean, soft,  
lint-free cloth. Then, leave them to dry completely in a well-ventilated  
location protected from direct sunlight.  
:
Never use hot air from a hair dryer or other appliance to dry the case  
and TTL cable, and never place them in direct sunlight to dry. This  
could deteriorate or deform the case, TTL cable and O-ring and lead  
to water penetration. When wiping the case, take care not to scratch it.  
CAUTION  
Using a clean cloth free of fibers, etc., a piece of lint-free tissue paper  
or a soft toothbrush, remove any foreign matter attached to the grooves  
of the O-rings. Also remove sand and dirt particles attached to the O-  
ring contact surfaces on the case.  
E-25  
E-26  
 
:
• When a mechanical pencil or a similar other sharp  
object is used to remove the O-ring or to clean the  
inside of the O-ring groove, the Case and the O-ring  
may be damaged and water leakage may be caused.  
• When the O-ring is checked with the fingertips, take  
care not to stretch the O-ring.  
• Never use alcohol, thinner, benzene or similar solvents  
or chemicals detergents to clean the O-ring. When such  
chemicals are used, it is likely that the O-ring will be  
damaged or that its deterioration will be accelerated.  
:
• Always perform maintenance of the waterproof  
function even when the Case has been opened to  
exchange the battery or the image storage during  
shooting. Neglecting this maintenance may become  
the cause of water leakage.  
• When the Case is not to be used for a long time,  
remove the O-ring from the groove to prevent  
deformation of the O-ring, apply a thin coat of silicone  
grease, and store it in a clean plastic bag or the like.  
• When drying is done with salt attached, it is likely that  
a function impairment will be caused. After use,  
always wash off any salt.  
CAUTION  
CAUTION  
Install the O-ring  
Confirm that no foreign matter is attached, apply a thin coat of the  
accessory grease to the O-ring, and fit the O-ring into the groove. At  
this time, confirm that the O-ring does not stick out from the groove.  
This sections explains how to apply lubricant to the camera case.  
Use the same procedure for the flash case.  
Replace consumable products.  
ț The O-ring is a consumable product. Independent of the number of  
times the Case is used, it is recommended that the O-ring should  
be replaced by a new one at least once a year.  
ț Deterioration of the O-ring is accelerated by the use conditions and  
the storage conditions. Replace the O-ring even before a year has  
passed if it shows signs of damage, cracking or loss of elasticity.  
How to Apply Grease to the O-ring  
Make sure there is no dirt on your  
Apply the  
specified grease  
fingers or on the O-ring; then  
squeeze about 5 mm of grease  
onto your fingertip.  
Note: Please use original Olympus products for the silicone O-ring  
grease, the silica gel, and the O-ring. These consumable  
products also can be purchased at an Olympus service  
station.  
1
2
3
4
Using two fingers and  
a
thumb,  
Spread the grease  
over the O-ring.  
spread the grease over the O-ring  
while rubbing it in. Use caution not to  
squeeze or pull the O-ring too hard.  
Once the grease has permeated  
throughout the O-ring, check it for damage  
or irregularities (both visually and by  
touch). If you notice any abnormalities,  
replace the O-ring with a new one.  
Check that there  
is no damage or  
irregularities on  
the O-ring.  
Apply the grease  
to the O-ring  
contact surface.  
Use any residual grease on your  
fingertips to clean and lubricate the O-  
ring contact surface on the front lid.  
E-27  
E-28  
 
operation parts and perform the advance test and the final test.  
(5) When not using this case, be sure to take the flash out.  
7. Appendix  
Q & A on the use of the PFL-01  
Q4: What cautions must be observed when opening and closing the Case?  
A4 : Pay special attention to the following items.  
(1) Do not open and close the Case at locations with water spray or sand spray.  
(2) Wipe off all waterdrops from the gap between the front lid and the rear lid  
and around projections and recesses such as the buckles. When this is  
not done, entry of waterdrops into the Case is to be feared at the time of  
opening and closing.  
(3) When opening the case, make sure no water from outside (e.g. dripping  
from your hair or diving suit)gets inside the case and/or on the flash!  
(4) When the Case is open, check that there is no attachment of sand, fibers  
or other foreign matter to the O-ring and the O-ring contact surface.  
(5) Never touch the flash with a hand wet with sea water.  
Q1: Which electronic flashes can be used with this case?  
A1 : The PFL-01 case is designed exclusively for the FL-20 Electronic Flash.  
Q2: What points should be observed when inserting the electronic flash into  
the case?  
A2 : When inserting the flash you should pay special attention to the following points:  
(1) Check that the flash’s batteries are fully charged.  
Insert the flash into the case’s hot shoe properly and tighten the flash’s  
shoe lock dial.  
(2) Before closing the case, check that the O-rings are correctly attached the  
case.  
(3) Make sure that the O-rings and contact surfaces are free of foreign  
matter such as hair and dirt.  
(4) Place the bag of silica gel in the case to avoid fogging. Only use  
Olympus silica gel.  
(5) Make sure that the TTL cable and hot shoe cable are connected firmly.  
(6) If you notice while diving that water has entered the case, stop the dive  
immediately and perform water leak test to check for water penetration. If  
any water has reached the electronic flash, do not use it, dry it  
immediately and contact your dealer or Olympus.  
Q5: How to handle the case after use?  
Q3: What cautions must be observed when using and storing the Case?  
A3 : Pay special attention to the following items.  
(1) When the O-ring contact surface is pressed strongly from the outside of  
the Case, or when the Case is twisted, the waterproof function may be  
impaired and water leakage may be caused.  
A5 : After using the case, remove the flash and rinse the case off in pure  
water as soon as possible. After use in salt water, you should immerse  
the case for an extended period of time in pure water. Operate the mode  
dial knob and buttons of the case when it is in clean tap water to remove  
any salt from their shafts. After rinsing, remove moisture with a dry cloth  
free of salt, and dry the case in the shade. Never use hot air from a hair  
dryer or other appliances to dry the case, and never place it in direct  
sunlight to dry, as this could deform, discolor, damage or deteriorates the  
case and O-rings. The inner side of the case should be wiped with a soft,  
lint-free cloth. Remove the O-rings, wipe off the attached foreign matter  
such as salt, sand and dirt, also clean the grooves in which O-rings have  
been fit and the surfaces in contact with O-rings, and dry all of them.  
When removing an O-ring from the groove, do not use a sharp object to  
avoid damaging the O-ring and causing leaks. Be always sure to use the  
provided pick for removing the O-ring.  
(2) When the Case is used, left or stored at the following locations, defective  
operation or trouble may be caused. Always avoid such locations.  
(a) Places where the Case can reach high temperatures under direct  
sunlight or in a car, places with extremely low temperatures, and  
places with extreme temperature variations.  
(b) Places with open fire  
(c) Places with volatile substances  
(d) Places with vibrations  
(3) The following instances could lead to operational problems and/or  
damage to this case and the flash inserted in it. Avoid knocks and  
sudden increase in pressure caused by:  
(a) Hitting other objects  
(b) Dropping  
(c) Placing heavy objects on top of the Case  
Q6: What points should be considered when using the case underwater?  
A6 : Please remember the following points.  
(1) Mount the case properly on a commercially available bracket or arm.  
(2) Adjust the case orientation so that the flash light is not obstructed.  
(3) Set the flash mode to TTL AUTO or MANUAL. (For the camera setup in  
(4) When the Case is not used for a long time, trouble from formation of  
mold etc. may be caused. Before use, confirm the operation of all  
E-29  
E-30  
 
these modes, refer to the instruction manual for the camera or flash.)  
Q7:How can I check for water leakage?  
A7 : Here you should carry out the first check and the final system check with  
the flash inside the case.  
and use it after applying a thin coat of the special grease. Excessive  
application of grease does not improve the waterproof function or the  
permissible withstand pressure. However, it may facilitate attachment of  
sand, dirt, etc.  
It is also recommended that you carry out the first check by diving to the  
intended depth with the empty case. If this is not possible, this test  
should be carried out at a depth of at least one meter or in a container of  
water (e.g. a bath, bucket, etc.). The final system check can then be  
carried out in a similar container of water.  
A thin, uniform coat produces the best result.  
(4) The O-ring is a consumable product. Replace it at least once a year.  
(5) Deterioration of the O-ring is accelerated by the use conditions and the  
storage conditions. Replace the O-ring immediately by a new one if it  
shows signs of damage, cracking or loss of elasticity.  
Q10  
:
Q8: What are the causes for entry of water?  
What are the important points for Case maintenance?  
Please observe the following items.  
A10:  
A8 : The main causes for the entry of water are shown below. Please check  
them most carefully.  
(1) Never use the following chemicals for cleaning, corrosion protection,  
defogging, repair or other purposes.  
(1) Forgetting to install the O-ring  
(2) The O-ring is partly or completely outside the groove.  
(3) Damage, deterioration, or deformation of the O-ring  
(4) Sand, fibers, hair or other foreign matter on the O-ring  
(5) Sand, fibers, hair or other foreign matter on the O-ring groove or the O-  
ring contact surface  
Never use alcohol, thinner, benzene or similar volatile organic solvents  
or chemical detergents to clean the Case. Pure water or lukewarm water  
is sufficient for cleaning.  
Do not use anticorrosion agents on the metal parts. The metal parts are  
made of aluminum, brass or stainless steel. Cleaning with pure water is  
sufficient.  
Do not use commercial defogging agents. Always use the original  
Olympus defogging silica gel.  
Do not use adhesive for repairs or other purposes. When repair is  
required, please contact a service station of our company or your dealer.  
(6) When the bag of silica gel is caught between the front and rear lids when  
closing the case.  
(7) Throwing the Case from a boat into the water, jumping with the Case into  
the water, or other sudden application of strong forces onto the Case.  
When entering the water, hand the Case over quietly or avoid impacts in  
other ways.  
Q11  
:
Please tell me about repairs.  
A11:  
Q9: What are the important points for O-ring maintenance?  
A9 : Please observe the following items.  
(1) Never use alcohol, thinner, benzene or similar organic solvents or  
chemical detergents to clean the O-ring. When such chemicals are used,  
it is to be feared that the O-ring will be damaged or that its deterioration  
will be accelerated.  
(2) Use the original Olympus silicone O-ring grease (white cap). The grease  
attached to Cases up to PT-008 (red cap) and the grease of other  
companies are not suitable for this silicone O-ring, and use of such  
grease may cause deterioration of the surface and impairment of the  
waterproof function.  
Please contact a service station of our company or your dealer, if repair  
should be necessary. Do not try to repair, disassemble or modify the  
Case yourself. Repair, disassembly or modification by you or third  
parties not authorized by Olympus invalidates the guarantee.  
Q12  
:
What are the model numbers of the PFL-01 accessories?  
The following accessories are being sold.  
A12:  
(1) O-ring for the PFL-01 body (POL-201A/ 1,000, POL-201B/ 1,000):  
This is a silicone rubber O-ring packing to be installed in the PT-019  
body to make it waterproof. O-rings for other Case models cannot be  
used.  
(3) In order to avoid deformation of the O-ring when the Case is not used for  
a long time, remove the O-ring from the Case, apply a thin coat of the  
special grease, and store the O-ring in a clean plastic bag. For reuse,  
confirm that the O-ring is free of damage and cracks, that it has sufficient  
elasticity, that the surface is free of stickiness and other abnormalities,  
(2) Silicone O-ring grease (PSOLG-1/ 800): This is a special grease for  
silicone O-ring maintenance.  
(3) Silica gel (SILCA-5/ 500): This is a desiccant used to prevent fogging  
of the glass parts of the Case. The quantity is five bags.  
You can order in large computer shops and camera mass sale stores.  
E-31  
E-32  
 
Please contact your dealer or a service station of our company when  
replacement is required. Replacement will be made against payment.  
How can I take good underwater photos?  
The web page of the visual college of the Club Camedia has a corner for  
underwater shooting techniques. Please take a look.  
After-sale Service  
You will receive the Warranty card from your dealer. Please make  
sure that the dealer's name, the date of purchase, etc. have been  
entered. If they have not been entered, immediately ask your  
dealer to have them entered. Read the guarantee conditions  
carefully and keep the guarantee card at a safe location.  
Please contact your dealer or one of the service stations of  
OLYMPUS CORPORATION listed in this instruction manual for  
questions on aftersale service for this product or in case of defects.  
In case of a defect of this product, occurring within one year after  
the date of purchase and with handling according to this instruction  
manual, repair based on the conditions specified in the guarantee  
card is performed free of charge.  
Q13  
:
A13:  
Payment is required for repairs after expiration of the guarantee  
period and for trouble caused by problematic handling by the  
customer even during the guarantee period.  
OLYMPUS CORPORATION keeps repair parts for this product for  
approximately five years after the end of production of the product.  
Accordingly, in principle repairs are accepted during this period. As  
repair may be possible even after this period, please contact your  
dealer or a service station in your neighborhood.  
Warranty is limited to and valid only in the region of intended  
distribution.  
Incidental damages from defects of this product (expenses  
required for diving, shooting expenses, loss of profit from photos,  
etc.) shall be excluded from the guarantee. In addition, transport  
expenses etc. related to repair shall be paid by the customer,  
independent of whether they are incurred during or after the  
guarantee period.  
E-33  
E-34  
 
Specifications  
MEMO  
Available models  
Olympus digital camera and  
Electronic Flash (FL-20)  
Pressure  
resistance  
Depth of up to 40 m  
Main materials  
Main body  
Buckle  
: Transparent polycarbonate  
: Stainless steel  
Buttons, arm mount screw, adapter  
: Nickel-plated brass  
Diffuser plate : Acrylic resin  
Dimensions  
Weight  
Width 111.5 mm x height 154.2 mm x thickness 76.2 mm  
(excluding the diffuser plate)  
325 g (without flash and accessories)  
We reserve the right to change the external appearance and the  
specifications without notice.  
Diver's Insurance Guide  
We recommend to subscribe to diver's insurance for water leakage.  
For details, refer to the enclosed Diver's Insurance Guide.  
E-35  
E-36  
 

Miele Washer W2444WPS User Manual
Milwaukee Coffee Grinder 4931 User Manual
NEC Server 120Lg User Manual
Nikon Camcorder COOLPIXS9100BLK User Manual
Nortel Networks IP Phone NN40050 109 User Manual
Olympus Camcorder LS 20M User Manual
Onkyo DVD Player CP702 User Manual
Panasonic Cell Phone EB A200 User Manual
Panasonic Digital Camera DMC FH1 User Manual
Panasonic Fax Machine KX PW76CL User Manual